
	************************************************
	***					     ***
	***   Ladder Master For Keyboard Operation   ***
	***					     ***
	************************************************


==========================================================
Type 1 : Moving the Cursor
==========================================================
	Up		 : Cursor Up one row

	Down		 : Cursor Down one row

	Left		 : Cursor Left one column

	Right		 : Cursor Right one column

	Home		 : First column

	End		 : Cursor Right to Output Area

	Control+PageUp	 : Top of page

	Contorl+PageDown : Bottom of page

	PageUp		 : Previous page

	PageDown	 : Next Page

	Control+Home	 : Top of Ladder

	Control+End	 : Bottom of Ladder
==========================================================



==========================================================
Type 2 : Ladder Component Placement
==========================================================
  Contact:
	A	   : Place a "Contact A" at cursor

	B	   : Place a "Contact B" at cursor

	Shift+S    : Place a "Contact S" at cursor

	H	   : Place a "Horizontal Line" at cursor
  --------------------------------------------------------
  Vertical Line:
	V	   : Place a "Branch" under cursor and 
                     cursor move down

	Shift+up   : Place a "Branch" on cursor

	Shift+down : Place a "Branch" under cursor
  --------------------------------------------------------
  Output Area:
	O,T,C	   : Place an Output Component at Output
		     Area

	S,R,U,D    : Place a SET,RST,PLS or PLF Component
		     at Output Area

	F	   : Place an Applied Instruction at
		     Output Area

    Note: Place "Horizontal Line" for Null from Cursor to
	  Output Area
==========================================================



==========================================================
Type 3 : Ladder Component Delete
==========================================================
	Del	   : Delete Component at cursor

	Shift+V    : Delete "Branch" under cursor
==========================================================



==========================================================
Type 4 : Ladder Edit Command
==========================================================
	E	  : Edit a Component at Cursor

	Control-E : 1.Scanning Ladder Program. Find and
		      Edit the no content components.

		     2.It is convenient for edit the
		       content of component after "Quick"
		       Mode.

		     3.'ESC' for Quit this edit mode

	BackSpace : 1.Delete a component at left of cursor

		     2.For Contact Area only

		     3.For simple serial area only. It is
		       no response for "Branch" and
		       "Bus Bar"
==========================================================



==========================================================
Type 5 : Alt Key Operation(same as PE2)
==========================================================
  Explanation:
	Mark Area : The Mark Area is built by Alt_L,
	Alt_B. It is purple area (default).

  Build Mark Area:

     Notice : 1.Building Mark Area needs cursor moving for
		range
	      2.Row is a basic unit for Alt_L
	      3.Cursor Area is a basic unit for Alt_B
	      4.The Mark Area doesn't change after the
		Mark Area operation.
	      5.The Operation break the branch. Recover by
		User or Compiler.

	Alt_L : Mark a line

	Alt_B : Mark a block

  Mark Area Operation:

	Alt_Z	  : Copy the Mark Area. It was built by
		    Alt_L

	Alt_M	  : Move the Mark Area. It was built by
		    Alt_L.

	Alt_O	  : Overwrite by the Mark Area. It was
		    built by Alt_B.

	Alt_D	  : Delete the Mark Area

	Alt+Left  : Move the Mark Area to the left

	Alt+Right : Move the Mark Area to the right

  Cancel Mark Area:

	Alt_U	  : Cancel Mark Area and the command of
		    Mark Area isn't availabe.
==========================================================



==========================================================
Type 6 : Row operation
==========================================================
	Control+down : Insert a row on cursor

	Control+up   : Delete a row

	Enter	     : Insert a row under cursor

==========================================================



==========================================================
Tytpe 7 : Edit Mode Setup
==========================================================
	Ins : Optional for Edit Mode (Insert or replace)
==========================================================



==========================================================
Function Key:
==========================================================
	F1 : Help Hot-Key
	F7 : Ladder Compile
	F8 : optional for Display Component Nickname
==========================================================



==========================================================
Hot_Key
==========================================================
	Control+N : New a File
	Control+O : Open a File
	Control+S : Save a File
	Control+A : Save as a File

	Control+P : Print

	Control+F : Component Search & Replacement

	Control+M : Monitor Mode Setup
	Control+Q : Exit Monitor Mode

	Control+D : Download program [ PC ---> PLC ]
	Control+U : Upload Program [ PC <--- PLC ]

	Control+R : PLC -- Remote Run
	Control+T : PLC -- Remote Stop
	Control+L : Modem Dialup
	Control+H : Hang Up
==========================================================
